Frankenbeute Wooden Hive

consisting of

• one wooden raised floor
• three wooden frames for 12 frames DN
  or 10 Zander frames
• one wooden lid
• External dimensions approx. 55 x 50 cm
  Height approx. 85 cm, weight approx. 20 kg
  
  without accessories

• Stainless steel ventilation and varroa grids
• Insert plate
• Inspection and working hatch
• Integrated mouse barrier
• Moving grid attachment frame
• External dimensions approx. 50.7 x 43.5 cm,
  height 12 cm, weight 3 kg

© Design registered with the DPMA and protected by law

for insertion from behind into the raised floor to facilitate varroa control. After treatment, we recommend removing the sliding drawer again so that the advantages of the raised floor, such as drum space and air circulation, can be utilized

against gamekeeping,
Dimensions approx: 388 x 389 mm

consisting of

• a wooden floor according to Pfefferle
• three wooden frames for 12 DN frames
  or 10 Zander frames
• one wooden lid
• External dimensions approx. 55 x 50 cm
  height approx. 85 cm, weight approx. 21 kg
  
  without accessories

• One stainless steel ventilation grille in the wooden frame and one Sticky Boards as a slide-in cassette, can be used variably from the top or bottom at the back
• Flight hole closure and mouse wedge
• Closure flaps at the front and rear
• External dimensions 55 x 49 cm, height 12 cm

Thickness approx. 38 x 17 mm, length 437 mm,
with 210 x 8 mm mouse slot

2-part
Large stainless steel pollen comb and
collecting frame for insertion from behind,
can be closed flush

suitable for 12 frames DN half or
10 frames Zander half.
External dimensions 57 x 50 cm, height 12 cm
Weight approx. 3 kg. Up to 34 mm thick wood

suitable for 12 frames DN flat or
10 Zander flat frames.
External dimensions 57 x 50 cm, height 17 cm
Weight approx. 4 kg. Up to 34 mm thick wood

suitable for 12 frames DN
or 10 Frames Zander.
External dimensions 57 x 50 cm, height 25 cm
Weight approx. 5 kg. Up to 34 mm thick wood

Made of 8 mm thick and waterproof glued plywood material and a solid wood upper beam, for beekeeping in an adapted brood chamber by using the wooden egg partition as a blind honeycomb
Length of upper beam 394 mm,
Length of the frame 370 mm,
total height 223 mm

You can find more differences here

for 12 frames DN or 10 frames Zander,
with all-round handle strip, display window,
insulating panel, glass pane and closing panel
Height 25 cm, weight approx. 5 kg.
Up to 34 mm thick wood

for 12 frames DN or 10 frames Zander. The highlight is the four hinged side panels, behind each of which there is an acrylic pane for an unobstructed view of the bee colony. The all-round handle strip also ensures good and safe carrying comfort

for approx. 10 liters of liquid feed with side access and sturdy aluminum perforated bracket.

We recommend painting the inside with vat paint Art. 2127 or ApiDana^® feed frame paint Art. 21275

made of 2 mm thick plastic with
angled cover and perforated aluminum plate
For placing on the rebate of an empty frame
only suitable for standard size and Zander, can be stacked after removing the angle cover to save space,
Size approx. 47.5 x 39.5 x 9 cm

Consisting of a wooden frame with flight hole, removable false bottom panel with two bung holes, Crown Boards and Inner Covers, wire frame with stainless steel ventilation grille. Can therefore be used in 6 ways: escape partition, intermediate floor with proboscis contact, closed intermediate floor, upper ventilator, upper flight hole and feed grid

Consisting of a wooden frame with flight hole, removable false bottom panel with two bung holes, Crown Boards and Inner Covers and round Bee Escapes. Can therefore be used in 2 ways as an escape partition or as a closed intermediate floor

is used instead of the bunghole plate in the wooden frame and thus allows a clear view into the colony
Dimensions: approx. 48.2 x 41.8 cm

with rebate, without entrance hole, consisting of wooden frame with bung plate and large 8 Bee Escapes. The Bee Escapes are supplied loose and fastened below the bunghole with thumbtacks, for example

© Design registered with the DPMA and protected by law

for insulation in the intermediate floors (Art. No. 1051 to 1057) as a winter cover and regulation of temperature and hive humidity
for insulation in the escape partition or Bee Escapes
Dimensions approx. 482 x 419 mm
Thickness approx. 19 mm

combines top ventilator and false bottom.
For attaching to the frames, so that the bee colonies do not get dusty when moving. With stainless steel ventilation grille and rebate. Also with closable entrance hole for use as a false bottom with proboscis contact.

Dimensions approx: 565 x 500 mm
Height 3 cm, weight approx. 2 kg

Is slipped over the outer lid
galvanized, conical fit
Inner support surface: 57 x 50 cm
Height 6 cm, weight approx. 2 kg

Is slipped over the outer lid
Inner support surface: 57.5 x 49.5 cm
Height 6 cm, weight approx. 2 kg

In pairs for the lateral storage of up to
five frames. Made of stainless steel.
Clear internal dimension 65 mm, suitable for
all Frankenbeute frames standard size / Zander

for support on the frame rebate
galvanized, size 500 x 425 mm

For support on the frame rebate
Stainless steel 1.4016, size 500 x 425 mm

for support on the frame seam
500 x 425 mm
3 mm thick

For placing directly on the frames,
only suitable for DN / Zander frames
Art. 1030, 1031 and 1032, galvanized
Size 395 x 476 mm

for placing on the frames,
0.4 mm thick and inherently stable
Size 500 x 430 mm

For placing on the frames,
0.32 mm thick and flexible
Size 500 x 430 mm

air-permeable, chained all round
rectangular size of approx. 505 x 435 mm
made from 100 % pure cotton

For placing on the frames
Size 500 x 570 mm

For placing on a Crown Boards and Inner Covers
Dimensions approx. 500 x 430 mm
Thickness approx. 5 mm

500 x 430 mm

Suitable for the Frankenbeute, among others
External dimensions of the hive cover plate
approx. 55 x 45 cm